The testing standards for cut gloves have changed for both ANSI and CE. If you're unsure about these changes, don't worry. We have provided a quick overview here and access to some information sheets below. You can also view the educational video provided by Paramount Safety below:

What to know about new EN 388:2016 and ANSI Cut Ratings

Basic Overview

  • The new EN 388 shield pictogram can report up to 6 separate mechanical performance measures.
  • These ratings include complementary scores for cut performance: the original Blade Cut test score (rating position 2) and the new EN ISO Cut Resistance score (rating position 5).
  • In instances where gloves have not been tested with the Blade Cut method or where this test is not applicable to that style (because blade dulling has occurred), the letter X can be used instead of a rating.

Previously, there was a 4 character performance rating, as below:

Position 1 - Abrasion Resistance
Position 2 - Blade Cut Resistance
Position 3 - Tear Resistance
Position 4 - Puncture Resistance

In the new version, Abrasion, Tear, and Puncture stay the same, but Cut Resistance moves to a letter rating from A to F, and appears at position 5. Manufacturers have a set amount of time to roll over to the new system, so some gloves may not change. If a manufacturer is choosing to update, you will see an 'X' where you would previously have seen the Cut Resistance number. This means that the company is choosing to only report under the new Cut Resistance test because a dulling effect occurs during the Coup Test, so it's not a true indicator of cut resistance under the new standard.

You should also see a character at position 6, this is your impact rating. It will either be a P for Pass, or an F for fail, or X for Not Tested. 

So, the new performance rating is:

Position 1 - Abrasion Resistance
Position 2 - Cut Resistance (Coup Test*)
Position 3 - Tear Resistance
Position 4 - Puncture Resistance
Position 5 - Cut Resistance (TDM-100 Test/EN ISO Cut Resistance Test**)
Position 6 - Impact Resistance


Gloves using the old EN388 standard may continue to be sold, because there is a 2 year compliance period. If you require impact or cut protection and your gloves don't show the updated markings, please ensure you refer to the manufacturer specification sheet to make sure you are using the best possible glove for your situation. 

Testing Methods:

The new EN388 standard changes with the formal inclusion of the ISO 13997 cut test method. It is similar to the ASTM F2992-15 test method and is also known as the TDM-100 Test. The TDM machine uses vertical force and a sliding blade, whereas the Coup test uses a rotating and linear blade movement with a fixed load. The Coup Test would produce a quickly dulling blade when testing yarns with high levels of steel fibres and glass, so could provide unreliable scores.


*Coup Test: In this test, a circular rotary blade moves back and forth with a defined force (5 newtons) on the test object until the blade breaks through the material. The sharpness of the blade is then measured against a cotton reference material. The result is displayed as an index value calculated first from the cycle count it took to cut through the cut-resistant material and then the reference material.

**TDM-100 Test/EN ISO Cut Resistance Test: In this text, a sliding blade and different weights are used. EN ISO Cut Resistance is graded A-E in newtons, as below:

EN388 Rating      Range (Newtons)      Converted Range (grams)      ANSI/ISEA 105 Level      Range (grams)
A 2 - 4.9 204 - 508 A1 200 - 499
B 5 - 9.9 509 - 1019  A2 500 - 999
C 10 - 14.9 1020 - 1529 A3  1000 - 1499
D 15 - 21.9 1530 - 2242  A4  1500 - 2199 
E 22 - 29.9  2243 - 3058  A5  2200 - 2999 
F 30+  3059  A6  3000 - 3999 



Ansell  - NEW EN 388:2016 Glove Marking Examples

Protective Industrial Products - Products Updated EN 388 Standard